Introduction to bathroom installation and acceptan

2022-07-22
  • Detail

Although the bathroom space is not large, you can't be careless in the decoration, especially the bathroom products. If they are not installed properly, it will be troublesome to reinstall them. Therefore, many decoration owners will pay attention to the installation details and put forward one or another requirements to the decoration master. After the bathroom is installed, it is also a knowledge for acceptance

although the bathroom space is small, you can't be careless in the decoration, especially the bathroom products. If they are not installed, it will be troublesome to reinstall them. Therefore, many decoration owners will pay attention to the installation details and put forward one or another requirements to the decoration master. After the installation of the bathroom, it is also a knowledge for acceptance. Next, I will introduce the whole strategy of sanitary ware installation and acceptance and various sanitary ware installation standards

bathroom installation and acceptance strategy

1 Check the bathroom cabinet

a, flexibility check

you can check the flexibility of the bathroom cabinet. The distance between the door and the frame and the drawer should meet the requirements, and whether it is flexible and free of friction, whether the door panel can be opened and closed smoothly, etc

b, the edge banding should be firm

the edge banding is very important for the protection of the bathroom cabinet. You can check the edge banding of the cabinet body and the door panel for bulges, tears, etc.

c, the contact should be tight

the distance between the table and the wall should be sealed, otherwise it is easy to store water before the cabinet body and the wall

2. Check the floor drain

to see whether it meets the requirements. The water on the ground should preferably flow to the floor drain, and there should be no residue

3. Check the shower room

the shower room should be strictly assembled. The appearance of the shower room should be clean and bright, the blocking door and the sliding door should be parallel and vertical to each other, and the two moving doors should be easy to open and close, close without gap and water leakage

4. Check the vertical basin or table basin

the lower foot of the vertical basin should be firmly connected with the floor. During installation, the foot should be sealed with silicone, without leakage. The basin should be firm, and the wooden cabinet can be used to support it stably under the stage. The basin without cabinet should be supported by an iron frame after being fixed with the wall, and the block surface course should be paved against the wall as a water retaining vertical plate, which is generally 8~12cm; A skirt of 10~12cm should be hung on the outside of the table panel, which can cover the iron frame. After installation, the place near the wall and around the basin should be sealed with silicone, without leakage

5. Check the toilet

check whether the pit distance of the toilet is reasonable. If the pit distance is too small, the water tank will enter the wall, which will affect the use; The pedestal pan shall be firm and can be fixed with expansion bolts instead of wood screws. Some toilet seats are sealed with rubber gaskets instead of grout, and then sealed with silicone after being firmly installed. The installation position of toilet and water tank shall be accurate. The allowable error of single piece position is 10mm, and the allowable error of perpendicularity should not be greater than 10mm

6. Check the bathtub

the drain of the bathtub should preferably be directly connected to the water spout. Do not connect it with plastic hoses. At the same time, it is against opening an open ditch under the cylinder for drainage. Acrylic bathtubs are easy to crack against the wall after a long time due to human body heavy load and hydrodynamic load, so the silicone sealing must be tight

various sanitary installation standards

1 The upper edge of the basin is 800-850mm away from the ground

2. Toilets are divided into wall drainage and ground drainage, which are generally divided into 300mm and 400mm hole spacing, which can be determined according to the drainage system form of the whole building

3. Upper key water tank: the finished height of the table top is 850mm. Front key water tank: the finished height of the table top is more than 1150mm

4. The adult urinal is 650-700mm from the ground, and the child urinal is 300mm from the ground

5. Towel ring: the lower edge is about 1000-1400mm from the ground

6. Tissue rack: the center is 650mm from the ground and 800mm from the rear edge of the toilet

7 Towel rack: 1600-1800mm from the ground

8 Bathtub: the height of the bathtub along the platform should preferably be 550-600mm

9 Shower: the top spray center of shower is 2050mm from the ground

10 Handheld shower: 1050mm from the center to the ground

editor's summary: This is the introduction of the whole strategy of bathroom installation and acceptance and various bathroom installation standards, hoping to be helpful to you. You can pay attention to information if you want to know more about it

南宁皮肤病医院

南昌眼科医院

绍兴男科医院

天津性病医院

Copyright © 2011 JIN SHI